Expert Answers about Jayco
- Replacement Hitch Hardware for Curt Adjustable Width Trailer Hitch 13703
- In order to replace the mounting hardware for the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 you'll want to go to the page for part # RHK and put that 13703 part number in the field for "Hitch Item Number". This will give you the replacement hardware kit for this hitch.
view full answer... - Replacement Fairing for Curt C18115 Roof Cargo Basket
- The closest alternative we offer for the # C18115-FAR replacement fairing would be the Rhino Rack # RRRF3 which is 44 inches long as opposed to the Curt # C18115-FAR which is 1 inch longer. The problem you'll run into by attempting to use a different fairing is that the mounting holes won't line up.
I'd recommend going with the fairing that was designed for use with your basket, the # C18115-FAR.
view full answer... - Replacement Brake Assemblies and Grease Seals for Dexter 4400 lb Trailer Axle
- I'm assuming the hubs are used on a 5th wheel, is that correct? For a tandem axle setup, the combined axle capacity would be 8800 lbs. The remainder is carried by the rear axle of the tow vehicle, since the pin weight of a 5th wheel is typically 20% of the GVWR, the axles are properly rated for your RV.
For replacement brake assemblies, I'd recommend the # K23-478-479 from Dexter, which includes right and left auto adjusting brake assemblies. After the initial setup, the brakes will constantly...
view full answer... - Radio Replacement for Jensen VR185 In Cab Stereo
- I do not have an exact replacement - but I have something similar.
Your Jensen VR125 stereo measured 3-1/2" tall by 7" inches wide.
The Jensen # JWM45 stereo measures 3-3/8" tall by 8-3/16" wide.
The odd sizing of your radio makes it difficult to find a replacement solution.
view full answer... - Replacement Lock Core And Lock Housing For Yakima RocketBox Cargo
- For your Yakima RocketBox Roof-Top Cargo Carrier the correct key and lock core is Yakima SKS Lock Cores # Y07202, which comes in a pack of two. In regard to the actual lock housing itself, you can use Replacement Hardware Kit for Yakima Q Towers 2007 and Newer # 8880046 if the product images match what your current lock housings look like. This includes the 4 housings, clips, and endcaps. This is the only lock housing available that may work for you; if it does not look the same then feel...
view full answer... - Availability For Replacement Base Plate Arms For Roadmaster Base Plate Kit
- We do have the replacement Roadmaster Base Plate Arms for the Roadmaster Direct-Connect Base Plate Kit - Removable Arms # RM-521567-5 on your 2014 Honda CR-V.
You will need the Roadmaster Replacement Arms for Base Plate Kits # RM-ARMS, and will need to fill out the order form found on the product page by clicking the instruction link tab.
If you are also needing a tow bar I recommend the Roadmaster Falcon All Terrain, Non-Binding Tow Bar # RM-522 as it is one of our most popular tow bars...
view full answer... - Replacement Brake Shoes for Dexter Hydraulic 12-1/4 Inch x 4 Inch Brakes
- The Dexter parts you've mentioned are the left and right brake shoe for a hydraulic brake that is 12-1/4" x 4". To replace those parts you can use the Replacement Hydraulic Shoe Lining for Dexter 10K Hydraulic Brakes - LH # BP04-340 and Replacement Hydraulic Shoe Lining for Dexter 10K Hydraulic Brakes - RH # BP04-350, which are the correct left and right brake shoe replacements.
view full answer... - 270 Awning Attached to Truck Camper Shell
- It will be no problem to attach a 270-degree awning like the Rhino-Rack "BatWing" # RR33100 for driver's side or # RR33200 for passenger side. This awning attaches to roof cross bars with channels. In this case, a good choice for cross bars would be the Rhino-Rack # Y02-480B Aero Bar Roof Rack for Camper Shells. I think you will like having tracks that can be adjusted for varying uses. Otherwise you can use your Yakima bars if they have a top track on them.
Many of our Rhino-Rack customers...
view full answer... - Is Bargman 30-84-509 the Replacement Taillight Assembly For 2002 Fleetwood Flair Class A Motorhome
- I don't have any database that would tell me which taillights were originally used on your 2002 Fleetwood Flair Class A motorhome, but after looking at several photos I found online, it looks like the Bargman # 30-84-509 is a likely fit.
The Bargman # 30-84-509 measures 14-1/16 inches wide and 5-15/16 inches tall. The holes for the mounting hardware are 6-1/4 inches apart on center measured from top to bottom and the side to side on center distance between the end holes is 13-1/2 inches....
view full answer... - Replacement 25-1/8 Inch Long Leaf Spring for 3500 lb Axle
- The PR4 leaf spring which we sell as # e28SR is not interchangeable with the PR4B which we sell as part # e54SR. The springs are different lengths and capacities, with the # e54SR being 25-1/8 of an inch long for a 3500 lb axle and the # e28SR being 25-1/4 inches long for a 5000 lb axle.
The correct way to measure for length is to jack the trailer up so the axle hangs free, then measure the eye to eye distance. This might be difficult because the springs are broken, but if they aren't...
view full answer... - Replacement Key N132 For Sportrack Cargo Box
- The correct replacement for the N132 key for your Sportrack cargo box is the following:
- Replacement Key for Thule Racks and Carriers - N132 # THKEYN132
view full answer... - Replacement Plastic Hardware for RV Glass Stove Cover
- The only replacement parts we offer for the hinged glass stove top cover is the actual hinge and then the bolt and nut used to secure it, the Replacement Hinge for Furrion 2-in-1 Range Oven part # LC719851. Unfortunately, we don't have any other parts or hardware so if this is not what you need I recommend trying out a local hardware store.
view full answer... - Replacement Wiper Seal Needed for 2019 Prism Elite 24EF Motorhome
- If the Rubber Wiper Seal for RV Slide Out # SR29FR you're looking at matches the dimensions of your current wiper seal then you can definitely replace it with this!
This seal measures 15' long x 3" wide and is 1/8" thick at the thickest part as you can see in the linked photo.
view full answer... - Availability of 2 Inch Ball for Reese Pro Round Bar Weight Distribution
- The Reese # RE94FR only requires a ball with a 1-1/4" diameter shank and the capacity to match the system. Although there are no specific balls from Reese, you can use the Curt # A-90 as a replacement for the 2-5/16" ball you have now. If you would prefer a stainless steel option you could use the # C69FR instead.
view full answer... - Replacement Toilet Base Seal for Dometic 300 Series Toilet
- The correct replacement seal for your Dometic 300 series toilet is the # DOM28FR. This has an outer diameter of 7-1/4" which will match your current seal.
view full answer... - Replacement Axles for 2017 Grand Design Reflection 29RS
- What you're looking for is an 86-1/2" long replacement axle. Since you will need new hubs and drums, along with brakes, I recommend getting the # 8327816-EB. This has a 71-1/2" spring center length so you will also need to cut off the spring seats and weld on # TRSS300 to match the current 68-1/2" measurement.
Grand Design does a great job listing their parts, but unfortunately they don't include the leaf spring information. You will need to measure your current leaf springs to find the...
view full answer... - Availability Of Replacement Stabilizer Bar For Roadmaster Dolly RM-3477
- We sure do!
I checked out the owner's manual for your Roadmaster Dolly model RM-3477 and found it uses the replacement Stabilizer Bar # RM-B001225.
view full answer... - Replacement Converter For Progressive Dynamics PD4560K18NS2 Power Center
- The Converter # PD4560CSV is the correct replacement for your PD4560K18NS2 as long as you are using lead acid batteries. If you have upgraded to Lithium batteries you will need the Converter # PD4560LICSV to prevent damage to the batteries.
view full answer... - Replacement For Power Gear Slide Out Motor 1010001663
- Thank you for that info and we do have the replacement for your Power Gear Slide-Out motor 1010001663; the correct part is the following:
- Replacement MT Gear Motor Assembly with Connector B for PowerGear Slide-Outs # LC46UD
view full answer... - Correct Replacement Tarp for a TruXedo TruXport Tonneau Cover on a 2019 Ram 1500
- Thanks for all the info! For your TruXedo TruXport Soft, Roll-Up Tonneau Cover # TX286901 you'll just need the Replacement Tarp for TruXedo TruXport Soft, Roll-up Tonneau Cover # TX2469-CVR.
Since these replacement covers are made to order, you'll need to also enter your serial number into the "Serial Number or Date Code" box on the # TX2469-CVR product page.
view full answer...
Go To Results